AGENT SKILL

component-stusb4500qtr

Audit the exact STUSB4500QTR USB-PD sink controller, PESD24VS1UB,115 CC protectors, and 0603WAF5101T5E external Rd option. Use for Board P power, USB-C, NVM, pin, reset, protection, DNP, bring-up, or substitution work.

License 许可
MIT
最近更新
2026-11-13
Stars
★ 0
Forks
0

01 前言 Front Matter

name
component-stusb4500qtr
description
Audit the exact STUSB4500QTR USB-PD sink controller, PESD24VS1UB,115 CC protectors, and 0603WAF5101T5E external Rd option. Use for Board P power, USB-C, NVM, pin, reset, protection, DNP, bring-up, or substitution work.

02 资源文件 7

03 SKILL.md 正文

STUSB4500QTR bundle

Run the central offline validator, then read all seven local JSON artifacts. Resolve the controller and both DNP subordinates independently. Cite source and fact IDs with their conditions and locators.

Exact DS12499 Rev 8 and UM2650 Rev 3 bytes are reproducibly retained as MANUFACTURER_MIRROR. Their dependent controller claims remain UNSOURCED under the primary-only trust policy; programmed and as-built state remain open. The UNI-ROYAL external-Rd family specification and Nexperia protector specification are independently available, but they do not close controller behavior. Direct manufacturer-primary retrieval attempts from st.com were made on 2026-08-02 (canonical DS12499/UM2650 resource paths, the STUSB4500 product page, a legacy UM2650 URL, and a community.st.com mirror link: every st.com path timed out and the community.st.com link redirected to its forum homepage instead of the file) and again on 2026-08-14 (direct curl: HTTP/2 to the canonical DS12499 path failed with a stream error, and HTTP/1.1 retries of the DS12499 PDF, UM2650 PDF, and product page all timed out with 0 bytes while control fetches to other domains returned HTTP 200), so both sources stay MANUFACTURER_MIRROR/SOURCE UNAVAILABLE at primary and every dependent verdict stays UNSOURCED. Do not re-attempt from memory or treat these dated failures as permanent; a future session may retry the same URLs.

Pin 23 (VREG_2V7) is documented decoupling-only, but Board P's generator loads it with R15/R16 4.7k I2C pull-ups and exposes it on debug pogo pad J3.3 (net U1.23 C30.2 R15.2 R16.2 J3.3, fact fact-stusb-vreg2v7-load). This is an explicit open coverage item (cov-stusb-vreg2v7-load) requiring a manufacturer-primary locator authorizing external DC loading of this pin, or a re-route decision, plus confirmation that the NVM-programming jig's logic levels match 2.7 V; it must close before any NVM-programming bench work begins.

For controller work, separate unpowered/dead-battery, reset, configuration-load, normal attached, explicit-contract, fault/recovery, and disconnect states. Treat open-drain 0 as asserted and Hi-Z as deasserted. Do not infer the programmed NVM image: require a normalized 40-byte artifact, byte-for-byte readback, reset reload, full power-cycle reload, and negotiated-output bench evidence. Record the as-received factory image before any write. Check the current ST endurance limit before authorizing repeated writes; the retained record deliberately leaves endurance open.

Provision only with a current-limited source that satisfies the documented VDD or VSYS operating range and with a common-ground I2C programmer using the board pogo interface. Keep the load disconnected for first power and verify VBUS, gate polarity, discharge timing, CC state, and fault registers in stages. Volatile register edits are not persistent NVM proof.

Apply the netlist assertions in interactions.json exactly. A deterministic wrong pin, missing series discharge resistor, wrong PMOS polarity, or unsafe voltage is a blocker; state-dependent negotiation, timing, thermal behavior, ESD performance, and as-built NVM contents require bench evidence.

Human component reference

Human projection of this bundle: rec-stusb4500qtr, rec-pesd24vs1ub, rec-rd-0603waf5101t5e. Those pages are generated from the JSON files here and add nothing to them — where the two disagree, this bundle is correct. See also the component catalog and the cross-component rules.

04 同仓库更多 Skills

Takazudo
Takazudo/zudo-circuit-doc

component-spec-audit

暂无简介

★ 0
Takazudo
Takazudo/zudo-circuit-doc

component-spec-audit

Audit exact electronic-component identities and evidence, and run the end-to-end workflow for adding or replacing a component. Use whenever circuit, schematic, PCB, BOM, firmware, bring-up, substitution or documentation work could depend on a component rating, pin, package, source, CAD asset, publication or interaction.

★ 0
Takazudo
Takazudo/zudo-circuit-doc

circuit-spec-integration

Audit behavior that spans more than one exact component, such as shared supplies, signal boundaries, startup and reset states, protection, sensing, thermal coupling, firmware assumptions and as-built state. Use whenever a question, substitution or design change involves several component records or a stage beyond a single datasheet.

★ 0
Takazudo
Takazudo/zudo-circuit-doc

component-example

Resolve exact EXAMPLE-MPN component limits and application constraints. Use whenever EXAMPLE-MPN, its LCSC ID, manufacturer, function, pins, package, substitution, bring-up, or firmware behavior is relevant.

★ 0
Takazudo
Takazudo/zudo-circuit-doc

component-xfcn-board-headers

Audit the exact XFCN PZ254V-11-06P C492405 male and PM254V-11-06-H85 C2832269 female six-position 2.54 mm board-to-board headers. Use for Boards P/L pin order, orientation, footprint, ratings, mating, stock, alignment, or substitution.

★ 0
Takazudo
Takazudo/zudo-circuit-doc

component-umw-ao3401a-c347476

Audit the exact UMW (Youtai Semiconductor) AO3401A C347476 P-channel load-switch MOSFET. Use for Board P Q1 identity, gate polarity, pinout, ratings, SOA, thermal behavior, bring-up, or substitution decisions.

★ 0